OI Roundtable

Looking for some good details on Allen Bradley Power Flex alarms, actually faults or alarms, I'm not sure of the difference exactly, but I'm getting a Ground Fault 13, am I looking at the drive being ground faulted? or the motor?

Thanks!

Quote from: 2106tech on June 14, 2018, 04:04:AM
I'm getting a Ground Fault 13

A ground fault in this case is likely in the motor, I think the fault list tells you to check not only the motor for grounds, but the external wiring also. There is no mention of a ground within the drive.

Here's an expanded list tof the Allen Bradley Power Flex Faults in random order:

• 2 Auxiliary Input
• 39 Phase V to Ground
• 88 Software Fault
• 3 Power Loss
• 40 Phase W to Ground
• 89 Software Fault
• 4 UnderVoltage
• 41 Phase UV Short
• 90 Encoder Quad Error
• 5 OverVoltage
• 42 Phase VW Short
• 91 Encoder Loss
• 7 Motor Overload
• 43 Phase UW Short
• 92 Pulse In Loss
• 8 Heatsink OvrTemp
• 48 Params Defaulted
• 93 Hardware Fault
• 9 Transistor OverTemp
• 49 Drive Powerup
• 100 Parameter Checksum
• 10* Heatsink Low Temp
• 51 Flt Queue Cleared
• 101-103 UserSet Checksum
• 12 HW Over Current
• 52 Faults Cleared
• 104 Power Boarrd Chksum1
• 13 Ground Fault
• 55 Cntrol Board Overtemp
• 105 Pwr Board Chksum2
• 15 Load Loss
• 63 Shear Pin
• 106 Incompat MCB-PB
• 16 Motor Thermistor
• 64 Drive OverLoad
• 107 Replaced MCB-PB
• 17 Input Phase Loss
• 69 DB Resistance
• 108 'eyw Anlg Cal Chksum
• 18 Hardware PTC
• 70 Power Unit
• 109 NVS I/O Checksum
• 20 TorqPrv Spd Band
• 71- 75 Port 1-5 Adapter
• 110 NVS I/O Failure
• 21 Output PhaseLoss
• 76* Port 6 Adapter
• 111* Power Down Csum
• 24 Decel Inhibit
• 77 IR Volts Range
• 121 I/O Comm Loss
• 25 OverSpeed Limit
• 78 Flux Amps Ref Rang
• 122 I/O Failure
• 28 See Manual
• 79 Excessive Load
• 130 Hardware Fault
• 29 Analog In Loss
• 80 AutoTune Aborted
• 131 Hardware Fault
• 33 Auto Rstrt Tries
• 81- 85 Port 1-5 DPI Loss
• 900-930 Fatal Faults
• 36 SW OverCurrent
• 86* Port 6 DPI Loss
• 38 Phase U to Ground
• 87 IXo VoltageRange

And here's a list of the Power Flex Alarms:

• 1 Precharge Active
• 15 Ground Warn
• 28 Ixo Vlt Range
• 2 UnderVoltage
• 16* Brake Slipping
• 29 Sleep Config
• 3 Power Loss
• 17 Dig In ConflictA
• 30 TB Man Ref Cflct
• 4 Start At PowerUp
• 18 Dig In ConflictB
• 31 PTC Conflict
• 5 Analog in Loss
• 19 Dig In ConflictC
• 32 Brake Slipped
• 6 IntDBRes OvrHeat
• 20 Bipolar Conflict
• 33 AdjVoltRef Cflct
• 8 Drive OL Level 1
• 21 Motor Type Conflict
• 34 Home Not Set
• 9 Drive OL Level 2
• 22 NP Hz Conflict
• 38 DPI Port1 Loss
• 10 Decel Inhibt
• 23 MaxFreq Conflict
• 39 DPI Port2 Loss
• 11 Waking 24 VHz Neg Slope
• 40 DPI Port3 Loss
• 12 Motor Thermistor
• 25 IR Volts Range
• 49 Torq Prove Cflct
• 13 In Phase Loss
• 26 Flux Amps Ref Range
• 50 Prof Step Cflct
• 14 Load Loss
• 27 Speed Ref Cflct
• 52 PI Config Conflict

*Firmware 6.002 and later only

This is nuts, I am back where I started at Ground Fault 13. Getting frustrated with the Powerflex alarms

(https://www.obsoleteindustrial.com/i24/power-flex-faults-alarms.png)